• Immersion type for 6" size header tank
• Service life: 10 million cycles or more
• High peak pressure and reduced low air consumption
• Port size: 1", Orifice size: 40mm
• Fluid temperature: -5 to 60°C. Operating pressure up to 1.6 MPa
• Pilot pressure 0.25 to 0.7 MPa
• No lubrication required
• Port size: 3/8 to 1 inch
• Orifice diameter: 2mm
• Power-saving circuit available
• 2 port N.C. or N.O. types; 3 port Universal type
• Diaphragm choice of EPDM, FKM or Kalrez®
• Wetted part material: PEEK (body/plate
• Orifice diameter: 1.6mm
• Power-saving circuit available as standard
• Choose standard or high-pressure type
• 2 port N.C. or N.O. types; 3 port Universal type
• Diaphragm choice of EPDM, FKM or Kalrez®
• Wetted part material: PEEK (body/plate)
• Orifice diameter: 1.5mm
• Available with power-saving circuit that reduces holding power consumption to 1W
• Diaphragm choice of EPDM, FKM or Kalrez®
• Fluid contact material: PEEK
• Orifice diameter of LVM11: 1.5mm
• Orifice diameter of LVM10: 1.4mm
• Available with power-saving circuit that reduces holding power consumption to 1W
• 2 port N.C. or N.O. types; 3 port Universal type
• Diaphragm choice of EPDM, FKM or Kalrez®
• Wetted part material: PEEK or PFA (body/plate)
• Available with power-saving circuit that reduces holding power consumption to 0.9W
• 2 port N.C. or N.O. types; 3 port Universal type
• Diaphragm choice of EPDM, FKM or Kalrez®
• Wetted part material: PEEK (body/plate)
• Orifice diameter: 0.8mm
• Available with power-saving circuit that reduces holding power consumption to 0.8W
• Diaphragm choice of EPDM, FKM or Kalrez®
• Fluid contact material: PEEK
• For steam (can also be used with air and water)
• Low pressure loss due to angle seat structure
• Low leakage of 10 cm3/min or less (rubber seal)
• Long service life: 3 million cycles (steam) 5 million cycles (air)
• Body material: stainless steel 316L equivalent, bronze (CAC)
• For use with steam
• Long service life: 3 million cycles
• Double guide rings to improve air filtration
• Reduced power consumption compared to previous version
• Port size 1/4 to 1 inch
• IP65 Enclosure
• IP65 enclosure
• Normally Closed and Normally Open type available, Class H coil
• Special construction improves service life when compared with current shading coil
• Power consumption: size 1 – 9 w; size 2 – 12 w; size 3 - 15w
• Body material: brass (C37), stainless steel
• Can be used with heated water
• IP65 enclosure
• For use with high temperature oil, viscosity not exceed 50mm²/s
• Fluid temperature: -5 to 100°C
• Class H coil insulation
• Port size: 1/4 to 1 inch. Flange: 32A to 50A
• Body material: brass, stainless steel
• Medium: high temperature oil, -5 to 100°C
• Maximum pressure: 1.5 MPa
• IP65 enclosure
• Valve type: Normally Closed, Normally Open
• IP65 enclosure
• Normally Closed and Normally Open Type available, Class B coil
• Special construction improves service life when compared with current shading coil
• Power consumption: size 1 - 4.5w; size 2 - 7w; size 3 - 10.5w
• Body material: brass (C37), stainless steel
• Direct air operated, 3 port valve
• Proper selection of body and sealing material permits application of a wide variety of fluids
• Common valve style is easy to use; operable as either N.C. or N.O.
• Port size: 1/8 to 3/8 inch
• Easy to disassemble and reassemble in a short time
• Direct air operated, 2 port valve for manifold
• N.C. or N.O. valve type
• Compatible with a wide variety of fluids
• Seal material: NBR, FKM, EPDM
• Max. system pressure: 1.0 MPa